Page 1 of 3 123 Last
Results 1 to 10 of 29
  1. #1
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Arrow Motorola secret codes

    MICRO-TAC "FLIP" SERIES

    This phone follows similar methods as outlined for the 8000 series above.

    Remove the battery and locate the three contacts at the bottom of the phone, the two outer contacts are raised and connect with the battery. The center contact is recessed, this is the Manual Test Mode connector.

    Now look at the battery contacts, the two outer ones supply power to the phone, the center contact is an "extra" ground. This ground needs to be shorted to the test mode connector on the phone. The easiest way to do this is to put a small piece of solder wick, wire, aluminum foil or any other conductive material into the recess on the phone. Having done this carefully replace the battery and turn on the power, if you have been successful the phone will wake up in test mode.

    TEST MODE PROGRAMING:

    Assuming you have completed one of the above steps correctly the phone will wake up in test mode when you turn the power on. When you first access test mode the phone's display will alternate between various status information that includes the received signal strength and channel number. The phone will operate normally in this mode. You can now access Service Mode by pressing the # key, the display will clear and a ' will appear. Use the following procedure to program the phone:

    1. Enter 55# to access programing mode.
    2. The * key advances to the next step. (NOTE that test mode programing does NOT have step numbers, each time you press the * key the phone will display the next data entry).
    3. The CLR key will revert the display to the previously stored data.
    4. The # key aborts programing at any time.
    5. To complete programing you must scroll through ALL entries until a ' appears in the display.
    6. Note that some entries contain more digits than can be displayed by the phone, in this case only the last part of the data can be seen.

    TEST MODE PROGRAMING DATA:

    STEP# #OF DIGITS/RANGE DESCRIPTION

    01 00000 - 32767 SYSTEM ID
    02 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 1 BELOW
    03 10 DIGITS MIN (AREA CODE & TEL#)
    04 2 DIGITS STATION CLASS MARK
    05 2 DIGITS ACCESS OVERLOAD CLASS
    06 2 DIGITS GROUP ID (10 IN USA)
    07 6 DIGITS SECURITY CODE
    08 3 DIGITS LOCK CODE
    09 3 DIGITS SERVICE LEVEL (LEAVE AT 004)
    10 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 2 BELOW
    11 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 3 BELOW
    12 0333 OR 0334 INITIAL PAGING CHANNEL
    13 0333 "A" SYSTEM IPCH
    14 0334 "B" SYSTEM IPCH
    15 3 DIGIT NUMBER PAGING CHANNEL (021 IN USA)
    16 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 4 BELOW

  2. #2
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    Steps 01 through 06 and 12 will repeat for NAM 2 if the second phone number bit has been enabled in step 11.

    NOTES:

    Take care with Motorola's use of "0" and "1". Some options use "0" to enable, some use "1".

    These are eight digit binary fields used to select the following options:

    1. (step 02 above, suggested entry is: 11101001 for "A" system, 10101001 for "B" sys)

    Digit 1: Local use mark, 0 or 1.
    Digit 2: Preferred system, 0 or 1.
    Digit 3: End to end (DTMF) dialing, 1 to enable.
    Digit 4: Not used, enter 0.
    Digit 5: Repertory (speed) dialing, 1 to enable.
    Digit 6: Auxiliary (horn) alert, 1 to enable.
    Digit 7: Hands free (VSP) auto mute, 1 to enable (mutes outgoing hands free audio until the MUTE key is pressed).
    Digit 8: Min mark, 0 or 1.

    2. (step 10 above, suggested entry is: 00000100)

    Digits 1 - 4: Not used in USA, enter 0.
    Digit 5: Single system scan, 1 to enable (scan A or B system only, determined by bit 2 of step 02. Set to "0" to allow user the option).
    Digit 6: Super speed dial, 1 to enable (pressing N, or NN SND will dial the number stored in memory location NN).
    Digit 7: User selectable service level, 0 to enable (allows user to set long distance/memory access dialing restrictions).
    Digit 8: Lock function, 0 to enable (allows user to lock/un-lock the phone, if this is set to 1 the phone can not be locked).

    3. (step 11 above, suggested entry is: 00000000)

    Digit 1: Handset programing, 0 to enable (allows access to programing mode without having to enter test mode).
    Digit 2: Second phone number (not all phones), 1 to enable.
    Digit 3: Call timer access, 0 to enable.
    Digit 4: Auto system busy redial, 0 to enable.
    Digit 5: Speaker disable, 1 to enable (use with select VSP units only, do not use with 2000 series mobiles).
    Digit 6: IMTS/Cellular, 1 to enable (rarely used).
    Digit 7: User selectable system registration, 0 to enable.
    Digit 8: Dual antennae (diversity), 1 to enable.

    4. (step 16 above, suggested entry is: 0011010 for portable and 0011011for mobile units)

    Digit 1: Not used, 0 only.
    Digit 2: Not used, 0 only
    Digit 3: Continuous DTMF, 1 to enable (software version 8735 and later)
    Digit 4: 8 hour time-out, 0 to enable (software version 8735 and later)
    Digit 5: Not used, 0 only.
    Digit 6: Failed page indicator, 0 to enable (phone beeps when an incoming call is detected but signal conditions prevent completion of the call).
    Digit 7: Portable scan, 0 for portable, 1 for mobile units.

  3. #3
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    C-SCAN OPTION:

    Newer Motorola phones are equipped with a feature called C-Scan, this is an option along with the standard A/B system selections. C-Scan allows the phone to be programed with up to five inhibited system ID's per NAM. This is designed to prevent the phone from roaming onto specified non-home systems and therefore reduce "accidental" roaming fees.

    1. C-Scan can only be programed from test mode, power phone up with the relevant test mode contact grounded (see above).
    2. Press # to access test mode.
    3. Press 18#, the phone will display "0 40000".
    4. Enter the first inhibited system ID and press *.
    Continue to enter additional system ID's if required. After the 5th entry the phone will display "N2". Press * to continue and add system ID's for NAM 2 as required.
    5. If an incorrect entry is made (outside the range of 00000-32767) the display will not advance, press CLR and re-enter. Use a setting of 40000 for any un-needed locations.
    6. When the last entry has been made press * to store and press # to exit, turn off power.

    LOCK/UNLOCK PROCEDURES:

    Phones with "LOCK" buttons: Press lock for at least 1/2 a second.

    Phones with a "FCN" button: Press FCN 5, note that 5 has the letter's "J,K, and L" for lock.

    Phones with no FCN or LOCK button: Press Control 5, control is the black volume button on the side of the handset.

    SYSTEM SELECT PROCEDURES:

    Phones with a RCL button: Press RCL *, then * to select, STO to store.

    Phones with no RCL button: Press Control * then * to select, # to store.

    Options are: CSCAn: Preferred/Non preferred with system lockout.
    Std A/b, or Std b/A: Preferred/Non preferred.
    SCAn Ab, or SCAn bA: Non preferred/Preferred
    SCAn A: "A" ONLY
    SCAn b: "B" ONLY
    HOME: Home only

    (these are typical options, some phone's vary. C-Scan only available on newer models and does not appear unless programed, see above

    GENERAL NOTES:

    HANDSETS: Most Motorola handsets are interchangeable, when a handset is used with a transceiver other than the one it was designed for the display will show "LOANER". Some features and buttons may not work, for instance if the original handset did not have a RCL or STO button, and the replacement does, you will have to use the control * or control # sequence to access memory and A/B system select procedures.

    MOTOROLA TEST MODE COMMANDS:

    01# RESTART (POWER OFF THEN ON)

    02# STATUS DISPLAY, ALTERNATES BETWEEN:

    ABC DEF where:

    ABC = Channel number
    DEF = Received sensitivity for that channel

    and: A B C D E F G where:

    A = SAT frequency (0=5970, 1=6000, 2=6030, 3=no channel lock)
    B = Carrier (0=off, 1=on)
    C = Signalling tone (0=off, 1=on)
    D = Power level (0 through 7)
    E = Channel mode (0=voice channel, 1=control channel)
    F = Receive audio mute (0=unmuted, 1=muted)
    G = Transmit audio mute (0=unmuted, 1=muted)

  4. #4
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    Press * to hold display and # to end.

    03# Reset call timers

    04# Initialize Tranceiver to following settings:

    Carrier = OFF
    Receive Audio = MUTED
    Transmit Audio = MUTED
    Signaling Tone = OFF
    Call Timer RESET and peroiodic resetting ENABLED
    SAT = OFF
    DTMF & Audio Tones = OFF
    Audio Path = To SPEAKER

    05# Turn Carrier ON
    06# Turn Carrier OFF
    07# Mute RECEIVE audio
    08# Unmute RECEIVE audio
    09# Mute TRANSMIT audio
    10# Unmute TRANSMIT audio
    11ABC# Load Synthesizer with ABC, where ABC=the channel number in decimal
    12A# Set RF power level to A, where A=1 to 7
    13# Power down phone
    14# Transmit signaling tone
    15# Stop transmit of signaling tone
    16# Transmit a five word reverse voice channel message, all words will be: "FF00AA55CC33"
    17# Transmit a two word reverse voice channel message, both words will be: "FF00AA55CC33"
    18# Display contents of NAM one address at a time, press * to advance, press # to exit. (Two digit number to the left is the ADDRESS, to the right is the DATA)
    19# Display software version
    20# Receive control channel messages counting correctable and uncorrectable errors. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display two three digit numbers. The first number is the number of correctable errors and the second is uncorredtable errors.
    21# Receive voice channel messages counting correctable and uncorrectable errors. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display two three digit numbers. The first number is the number of correctable errors and the second is uncorredtable errors.
    22# Receive control channel messages counting word sync sequences. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display the number of word sync sequences in the display.
    23# Receive voice channel messages counting word sync sequences. When the command starts the number of the command will be displayed in the upper right hand corner of the display. Entering a # will terminate the test and display the number of word sync sequences in the display.
    24# Turn SAT transmission ON
    25# SAT OFF
    27# Transmit continuous control channel data, all words are: "FF00AA55CC33". When the command starts the number of the command will be displayed in the upper right hand corner of the display. Press # to terminate the test.
    28# Activate high tone (1150 Hz +/- 55 Hz)
    29# Deactivate high tone
    30# Activate low tone (770 Hz +/- 40 Hz)
    31# Deactivate low tone
    32# Initialize all non-volatile memory to zeros. Resets unit and makes it look "new".
    33A# Activate DTMF tone where A = DTMF digit 0 thru 9
    34# Deactivate DTMF
    35A# Send audio path to A where A = 0 for handsfree, 1 for speaker, 2 for alert, 3 for Handset
    36ABC# Activate channel scan, ABC is scan speed in milliseconds. Tunes from channel 1 to 666. Press * to pause scan and display RSSI, if scan speed is 300 milliseconds or greater the RSSI is displayed with each channel, if scan is less than 300 milliseconds the RSSI is only displayed when you press *
    37# not used
    38# Display serial number in hex (ESN). Displayes the byte number in the upper right side of the display and the data to the left, press * to step through the bytes, press # to exit.
    39# Receive one control channel word, when the word is received it will be displayed in hex. Command terminates when the word has been received or when # is pressed.
    40# Receive one voice channel word, when the word is received it will be displayed in hex. Command terminates when the word has been received or when # is pressed.
    41# (F19CTA models only) Enables the diversity antenna option on mobiles so equipped.
    42# Disable diversity.
    43# Disable diversity and force the mobile to use the TRANSMIT antenna.
    44# Disable diversity and force the mobile to use the RECEIVE antenna.
    45# Display the RSSI reading taken on the current channel.
    46# Display the cumulative call timer.
    47A# Set audio level to A where A = 0 lowest, A = 6 highest, or A = 7 muted.
    48# Turn sidetone on
    49# Sidetone off
    50# Maintenance data is transmitted and test results displayed: PASS =Received data is correct, FAIL1 = No data received within 2 seconds, FAIL2 = Received data is incorrect.
    51# Maintenance data is transmitted and looped back and test results displayed: PASS = Looped back data is correct, FAIL1 = No data looped back within 2 seconds, FAIL2 = Looped back data is incorrect.
    52A# Set phase adjustment. A decimal number thet corresponds to phase shift compensation in 4.5 degree increments. Compensation added to the inherant phase shift of the tranceiver to acheive a total phase shift of 0 (zero) degrees. Do not enter any value other than from the following list:

  5. #5
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    # entered, Degree of shift
    0 0 59 121.5 86 243.0
    1 4.5 60 126.0 87 247.5
    2 9.0 61 130.5 112 252.0
    3 13.5 62 135.0 113 256.5
    4 18.0 63 139.5 114 261.0
    5 22.5 40 144.0 115 265.5
    6 27.0 41 148.5 116 270.0
    7 31.5 42 153.0 117 274.5
    16 36.0 43 157.5 118 279.0
    17 40.5 44 162.0 119 283.5
    18 45.0 45 166.5 120 288.0
    19 49.5 46 171.0 121 292.5
    20 54.0 47 175.5 122 297.0
    21 58.5 64 180.0 123 301.5
    22 63.0 65 184.5 124 306.0
    23 67.5 66 189.0 125 310.5
    48 72.0 67 193.5 126 315.0
    49 76.5 68 198.0 127 319.5
    50 81.0 69 202.5 104 324.0
    51 85.5 70 207.0 105 328.5
    52 90.0 71 211.5 106 333.0
    53 94.5 80 216.0 107 337.5
    54 99.0 81 220.5 108 342.0
    55 103.5 82 225.0 109 346.5
    56 108.0 83 229.5 110 351.0
    57 112.5 84 234.0 111 355.5
    58 117.0 85 238.5

    53# Enable scrambler option, if equipped.
    54# Disable scrambler option, if equipped.
    55# Test Mode programming.
    58# Compandor on. Audio compressor and expandor on.
    59# Compandor off. Audio compressor and expandor off.
    61# Serial number transfer, not all models.
    62# Turn on audio ringer path.
    63# Turn off audio ringer path.
    70# Abbreviated field transmitter audio deviation command for tranceivers with FCC ID: ABZ89FT5668.
    71# Abbreviated field power adjustment command for tranceivers with FCC ID: ABZ89FT5668.
    72# Field audio phasing command.
    73# Field power adjustment command.

  6. #6
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    Motorola 6200


    Activate RBS

    (Note: pause means the * key held in until box appears)
    To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]
    You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it.

    De-activate RBS

    To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]
    This only works with some versions of software.

    These countries has been reported working:

    UK (Orange)
    AU

    What's the use of RBS:

    Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

    Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected.

    Pin Outs

    Numbered left to right, keypad up, battery down

    1. Audio Ground
    2. V+
    3. True data (TD) (input)
    4. Downlink - Complimentary data (CD) (input)
    5. Uplink - Return data (RD) (output)
    6. GND
    7. Audio Out - on/off
    8. Audio In
    9. Manual Test - ???
    10. Battery Feedback
    11. Antenna connector

  7. #7
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    MOTOROLA 6200 / 7500 / 8200 / 8400 / 8700



    To activate RBS (Engineering Menus):

    [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]

    (pause means the * key held in until box appears)

    You now have to press the [MENU] and scroll to the
    'Eng Field Options' function with the < or > keys, and enable it.

    To de-activate RBS (Engineering Menus):

    [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]

    (pause means the * key held in until box appears)

    Works on 6200's,8200's,1-888's,7500's,8400's and GSM StarTacs
    with later than version .27 software.

    Options under Eng Field Options

    Eng Field Options
    Active Cell
    RxLev -55Received powerlevel in dBm

    NCC 0National Colour Code, used for identifying channel

    BCC 7Broadcast Colour Code, also for identifying purposes

    MSTxPwr 35Max allowed transmit power 35dBm about 3.2W

    Time Adv xxxxxx is a number. Multiply this number by 550,and the result is the distance from the RBS (Radio Base Station), in meters.
    Adjacent Cells
    Adj Cell 1

    Channel 0033Channel Number

    RxLev -65Received powerlevel in dBm

    BCCH DecodeI think it means it is able to decode thechannel information contained in the BCCH

    RxLevAM -104Min allowed reception, compare with RxLev -65 and you get the C1 value which is 39 and reported back to base asmeasure of field strength.

    MTxPwr 35 Aain max allowed powerlevel

    C1 003 ??

    NCC 0 National Colour Code

    BCC 6 Broadcast Colour Code
    System Parameters
    Combined Off ??

    AcsClas 0000 Allows different priorities - this network doesn't support it.

    MCC 505 Mobile Country Code, 505 for Australia, 240 for Swedes etc

    MNC 01Mobile Network Code, 01 for Mobilenet, 02 for Optus, 03 for Vodafone using MCC 505. MCC+MNC is often called Network Code

    LAC 08720Location Area Code, shows which exchange your're in

    CellID 00473Base Station Identity

    T3212 005Time between periodic network updates (either hours between or time remaing until update, not sure)

    BS-PA-MFRM 4 ??

    XZQTY 14.3 ??
    Motorola Flip Pinout:

    ANT- (O) | | | | | | | | | |

    10 9 8 7 6 5 4 3 2 1

    Top of phone (screen)
    1) Audio Ground

    2) Ext b+

    3) T Data

    4) C Data

    5) R Data

    6) Logic Ground

    7) Audio Out - on/off

    Cool Audio In

    9) Manual Test

    10) Battery Feedback

  8. #8
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    Motorola 7500


    Activate RBS

    (Note: pause means the * key held in until box appears)
    To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]
    You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it.

    De-activate RBS

    To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]
    This only works with some versions of software.

    These countries has been reported working:

    IT (model: F16 HW: 5.2 SW: 2.1)


    What's the use of RBS:

    Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

    Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected.

    Pin Outs

    Numbered right to left, keypad up, battery down looking

    1. Gnd
    2. Pos
    3. True data (TD) (input)
    4. Complimentary data (CD) (input)
    5. Return data (RD) (output)
    6. Audio gnd
    7. Audio out
    8. Audio in

  9. #9
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    Motorola 8200


    Activate RBS

    (Note: pause means the * key held in until box appears)
    To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]
    You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it.

    De-activate RBS

    To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]
    This only works with some versions of software.

    These countries has been reported working:

    ES, AU, NL, BE


    What's the use of RBS:

    Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

    Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected.

    Pin Outs

    Numbered right to left, keypad up, battery down looking

    1. Audio Ground
    2. V+
    3. True data (TD) (input)
    4. Downlink - Complimentary data (CD) (input)
    5. Uplink - Return data (RD) (output)
    6. GND
    7. Audio Out - on/off
    8. Audio In
    9. Manual Test - ???
    10. Battery Feedback
    11. Antenna connector

  10. #10
    0 RP
    ash1986's Avatar
    Join Date
    Jun 2007
    Country
    India
    Posts
    27
    Thanks
    0

    Default

    Motorola 8400



    Activate RBS

    (Note: pause means the * key held in until box appears)
    To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]
    You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it.

    De-activate RBS

    To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]
    This only works with some versions of software.

    These countries has been reported working:

    IT, NL

    What's the use of RBS:

    Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

    Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected.

    Pin Outs

    Numbered left to right, keypad up, battery down

    1. Audio Ground
    2. V+
    3. True data (TD) (input)
    4. Downlink - Complimentary data (CD) (input)
    5. Uplink - Return data (RD) (output)
    6. GND
    7. Audio Out - on/off
    8. Audio In
    9. Manual Test - ???
    10. Battery Feedback
    11. Antenna connector

Page 1 of 3 123 Last