Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 29
  1. Default

    Motorola 8700


    *#06# for checking the IMEI (International Mobile Equipment Identity)

    Activate RBS

    (Note: pause means the * key held in until box appears)
    To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]
    You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it.

    De-activate RBS

    To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]
    This only works with some versions of software.

    These countries has been reported working:

    AU, IT, SG, DE, ES, ZA

    What's the use of RBS:

    Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

    Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected

  2. Default

    Motorola Analogue Phones


    MOTOROLA PROGRAMMING INSTRUCTIONS
    NOTES: Some units have dual NAM's.
    The ESN prefix is 130 decimal, 82 hex.

    Determine which access sequence to use:

    HAND HELD PORtable MODELS

    If the phone has a FCN button and no MENU button use sequence 1.
    If the phone has no FCN button use sequence 2.
    If the phone has a MENU button and a FCN button use sequence 4.

    INSTALLED MOBILE PHONES AND TRANSPORtable MODELS

    If the phone has no FCN button and no RCL button use sequence 3.
    If the phone has a FCN button use sequence 4.
    If the phone has a MEM button use sequence 5.
    If the phone has a RCL button and no FCN button use sequence 6.

    SEQUENCE# ACCESS CODE

    1 FCN (SECURITY CODE TWICE) RCL
    2 STO # (SECURITY CODE TWICE) RCL
    3 CTL 0 (SECURITY CODE TWICE) *
    4 FCN 0 (SECURITY CODE TWICE) RCL
    5 FCN 0 (SECURITY CODE TWICE) MEM
    6 CTL 0 (SECURITY CODE TWICE) RCL

    The default security code is 000000. The CTL (control) button is the single black button on the side of the handset.

    NAM programing:

    1. Turn the power on.
    2. Within ten seconds enter the access sequence as determined above.
    3. The phone should now show "01" in the left of the display, this is the first programing entry step number. If it does not the security code is incorrect, or the programing lock-out counter has been exceeded. In either case you can still program the unit by following the steps under TEST MODE PROGRAMING below.
    4. The * key is used to increment each step:
    Each time you press * the display will increment from the step number, displayed on the left, to the data stored in that step, displayed on the right. When the data is displayed make any necessary changes and press * to increment to the next step number.
    5. The SND key is used to complete and exit programing when any STEP NUMBER is displayed.
    If you have enabled the second phone number bit in step 10 below then pressing SND will switch to NAM 2. Steps 01 thru 06, 09 and 10 will repeat for NAM 2, the step number will be followed by a "2" to indicate NAM two.
    6. The CLR key will revert the display to the previously stored data.
    7. The # key will abort programing at any time.

    PROGRAMING DATA:

    STEP# #OF DIGITS/RANGE DESCRIPTION

    01 00000 - 32767 SYSTEM ID
    02 3 DIGITS AREA CODE
    03 7 DIGITS TEL NUMBER
    04 2 DIGITS STATION CLASS MARK
    05 2 DIGITS ACCESS OVERLOAD CLASS
    06 2 DIGITS GROUP ID (10 IN USA)
    07 6 DIGITS SECURITY CODE
    08 3 DIGITS LOCK CODE
    09 0333 OR 0334 INITIAL PAGING CHANNEL
    10 6 DIGIT BINARY OPTION PROGRAMING (SEE NOTE 1)
    11 3 DIGIT BINARY OPTION PROGRAMING (SEE NOTE 2)

    NOTES:

    Take care with Motorola's use of "0" and "1". Some options use "0" to enable, some use "1".

    1. This is a 6 digit binary field used to select the following options:

    Digit 1: Internal handset speaker, 0 to enable.
    Digit 2: Local Use Mark, 0 or 1.
    Digit 3: MIN Mark, 0 or 1.
    Digit 4: Auto Recall, always set to 1 (enabled).
    Digit 5: Second phone number (not all phones), 1 to enable.
    Digit 6: Diversity (Two antennas, not all phones), 1 to enable.

    2. This is a 3 digit binary field used to select the following options:

    Digit 1: Continuous DTMF, 1 to enable.
    Digit 2: Transportable Ringer/Speaker, 0=Transducer, 1=Handset.
    Digit 3: 8 hour time out in transportable mode, 0 to enable.

    TEST MODE ACCESS:

    INSTALLED MOBILE PHONES AND TRANSPORtable MODELS

    To enter test mode on units with software version 85 and higher you must short pins 20 and 21 of the transceiver data connector. An RS232 break out box is useful for this, or construct a test mode adaptor from standard Radio Shack parts.

    For MINI TR or Silver Mini Tac transceivers (smaller data connector) you can either short pins 9 and 14 or simply use a paper clip to short the hands free microphone connector.

    HAND HELD PORtable MODELS:

    There are two basic types of Motorola portable phones, the Micro-Tac series "Flip" phones, and the larger 8000 and Ultra Classic phones. Certain newer Motorola and Pioneer badged Micro-Tac phones do not have a "flip", but follow the same procedure as the Micro-Tac.

    8000 & ULTRA CLASSIC SERIES:

    If you have an 8000 series phone determine the "type" before trying to enter test mode. On the back of the phone, or on the bottom in certain older models, locate the F09... number this is the series number. If the FOURTH digit of this number is a "D" you CAN NOT program the unit through test mode, a Motorola RTL4154/RTL4153 programer is required to make any changes to this unit.

    Having determined that you do not have a "D" series phone the following procedure is used to access test mode:

    Remove the battery from the phone and locate the 12 contacts at the top near the antenna connector. These contacts are numbered 1 through 12 from top left through bottom right. Pin 6, top right, is the Manual Test Mode Pin. You must ground this pin while powering up the phone. Pin 7 (lower left) or the antenna connector should be used for ground. Follow one of these procedures to gain access to pin 6:

    1. The top section of the battery that covers the contacts contains nothing but air. By careful measuring you can drill a small hole in the battery to gain access to pin 6, alternately simply cut the top off the battery with a hack saw. Having gained access use a paper clip to short pin six to the antenna connector ground while powering up the phone.
    2. If you do not want to "destroy" a battery you can apply an external 7.5 volts to the + and - connectors at the bottom of the phone, ground pin 6 while powering up the phone as above.
    3. You can also try soldering or jamming a small jumper between pins 6 and 7 (top right to lower left), or between pin 6 and the antenna connector housing ground. Carefully replace the battery and power up the phone. Use caution with this method not to short out any other pin.
    4. A cigarette lighter adaptor, if you have one, also makes a great test mode adaptor as it can be disassembled to give you easier access to pin 6. Many are pre marked, or even have holes in the right location. This is because they are often stamped from the same mold that the manufacturer uses for making hands free adaptor kits and these kits require access to the phone's connectors.

  3. Default

    Motorola CD 160, CD 520, 920, 930


    Motorola CD 160

    Press menu and type one of these numbers and press OK:

    11 = Status Review
    13 = Available Networks
    14 = Preferred Networks
    22 = Select Keypad Tones
    25 = Require SIM Card PIN
    26 = Language Selection
    32 = Repetitive Timer
    33 = Single Alert Timer
    34 = Set IN-Call Display
    35 = Show Call Timers
    36 = Show Call Charges
    37 = Call Charge Settings
    38 = Reset All Timers
    43 = Reset All Timers
    45 = Show Last Call
    46 = Total For All Calls
    47 = Lifetime Timer
    51 = Change Unlock Code
    52 = Master Reset
    53 = Master Clear (Warning!! May result in deleting the Message Editor!!!)
    54 = New Security Code
    55 = Automatic Lock
    63 = Battery Saving Mode

    Free call tip

    1 Enter the phone number
    2 Enter OK
    3 Type *#06#
    4 Press Button C
    5 And finally press the button for power off.

    You should now be able to talk without being billed.

    Motorola CD 520

    Free call tip

    1 Enter the phone number
    2 Enter OK
    3 Type *#06#
    4 Press Button C
    5 And finally press the button for power off.

    You should now be able to talk without being billed.

    Motorola 920/930

    The 54# Tip:

    Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone number used for with this key when speed dialing.

  4. Default

    Motorola d460



    *#06# for checking the IMEI (International Mobile Equipment Identity)

    Activate RBS

    (Note: pause means the * key held in until box appears)
    To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]
    You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it.

    De-activate RBS

    To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]
    This only works with some versions of software.

    What's the use of RBS:

    Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

    Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected.

  5. Default

    Motorola d460, 2500, 6200 (Flare), 7500, 8200, 8400 & 8700




    IMEI
    *#06# displays IMEI on 8700, NOT on 6200, 7500, 8200


    To activate RBS:

    (pause means the * key held in until box appears)

    [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]

    You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it.

    To de-activate RBS,

    [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]

    This only works with some versions of software. Please report what works and doesn't for you.

    Reported working, by country:

    d460: IT
    6200 Flare: UK (Orange), AU
    7500: IT (model: F16 HW: 5.2 SW: 2.1)
    8200: ES, AU, NL, BE
    8400: IT, NL
    8700: AU, IT, SG, DE, ES, ZA
    Uses of RBS:

    Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

    Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected.

  6. Default

    Motorola Elite



    Test Mode

    To enter in Nam programming Mode, press:
    [arrow up]
    000000000000 (12 times zero)
    [MR]

    now display shows the first step of NAM programming; simply enter data and move to the next step using:

    * (the same key of [left arrow])

    Software version

    To see software version of your phone you need to short-circuit antenna ground with the two nearest pin together in the connector located under the phone. then:
    Power ON the phone

    and type:

    #19#

    now display is showing software version of your phone.
    Serial Number

    To see the serial number of your phone you need to short-circuit antenna ground with the two nearest pin together in the connector located under the phone. then:
    Power ON the phone

    and type:

    #75#

    now display is showing the first pair of digits, then go ahead using

    * (the same key of [left arrow])

    to show the second pair and so on.

    Pinout

    The pins are numbered 1 thru 10 from right to left
    ANT- (O) | | | | | | | | | |

    1) Audio Ground
    2) Ext b+
    3) T Data
    4) C Data
    5) R Data
    6) Logic Ground
    7) Audio Out - on/off
    Cool Audio In
    9) Manual Test
    10) Battery Feedback

  7. Default

    Motorola Flare



    Functionality Enablement

    Following you'll find the procedure in order to get more menu's from your phone. But you don't just get more menu's, you'll get 99 more memories available, giving a total of 198 memories! These memories are stored in the phone, not in the SIM, which means you can store many more characters and numbers for each name.
    Before you begin, take note that:

    Make a note of your voicemail number! You may lose it during this! (don't worry, you can reprogramme it later).
    You may need to use the master reset option to get outgoing DTMF going again after this.
    All the menu's seem to be dependant on others being available, so if you just activate one, it will say not available
    Lastly, p = a pause. ie, what you get when you hold down the * button for 3 seconds.
    And then .... let's go !

    First of all, press

    ppp070p0p OK

    You have just turned off the code that disables further changes. This seems to have been set in some phones.
    Now enter:

    ppp000p1p OK
    ppp001p1p OK
    ppp002p1p OK

    all the way to

    ppp113p1p OK

    but AVOID ppp070p1p and ppp007p1p

    Don't worry, this only takes about 35 mins for all 111, but just don't lose count!

    Then go to phone setup menu, and select extended menu

    And finally ....

    You'd find some more menu items which wasn't there before and you got 99 more memory locations giving a total of 198 memories.

    Show IMEI code

    If you need to know what's the IMEI code of your phone, simply press:
    * # 06 #

    you'll read it on display.

    Pinout

    Numbered left to right, keypad up, battery down
    1) Audio Ground
    2) V+
    3) True data (TD) (input)
    4) Downlink - Complimentary data (CD) (input)
    5) Uplink - Return data (RD) (output)
    6) GND
    7) Audio Out - on/off
    Cool Audio In
    9) Manual Test - ???
    10) Battery Feedback
    11) Antenna connector

    To switch to the external antenna, a 2k2 resitor shout be placed in the coaxial antenna cable from shield to core.

  8. Default

    Motorola MicroTac



    Test Mode

    To enter in Nam programming Mode, you need to short-circuit the first and the third battery pin from the right, then:
    Power ON the phone

    display will show "Tacs5", type in:

    55

    now display shows the first step of NAM programming; simply enter data and move to the next step using:

    * (the same key of [left arrow])

    Software version

    To enter in Nam programming Mode, you need to short-circuit the first and the third battery pin from the right, then:
    Power ON the phone

    display will show "Tacs5", type in:

    19

    now display is showing software version of your phone.

    ================================================== ==============================
    =================================================

    Motorola StarTac



    Show IMEI code

    If you need to know what's the IMEI code of your phone, simply press:
    * # 06 #

    you'll read it on display.

    Pinout

    1) Connected with 22pf to pin 3
    2) RF out
    3) Connected with 33 pf to pin 8, 33 pf to pin, 33 pf to pin 7
    4) BAT_FDBAK
    5) MAN_TEST connected with 10k to L275
    6) RS232_TX - connected to MCU SPI bus
    7) RS232_RX - connected to MCU SPI bus
    Cool AUDIO_IN
    9) AUDIO_OUT
    10) Connected with 33 pf to pin 13, 33 pf to pin 14
    11) UPLINK -|
    12) DOWNLINK -|- DSC bus connected to the BIC
    13) DSC_EN_B -|
    14) EXT_B+
    15) Gnd

    ================================================== ==============================
    ======================================

    Motorola V3688



    *#06# for checking the IMEI (International Mobile Equipment Identity)

    Enhanced Full Rate Codec (EFR):

    To Enable EFR press [][][] 119 [] 1 [] OK.
    To Disable EFR press [][][] 119 [] 0 [] OK

    NOTE: Nothing appears on Screen.

  9. Default Motorola phone help

    this may help someone ...

    If your phone doesn't turn on, or even powers on for half a second and then keeps going through a power cycle by itself, your phone has a corrupt flash.

    This CAN be fixed though.
    You must take the phone and put it into bootloader mode.
    It varies on each phone how you do it, but holding * and # and then power is the most common way.
    If your phone wont even power on, then it may take some time to get it to turn on. Took me 3 days once.
    I did find that by plugging it into the USB port while attempting bootloader helped later on speed that process up.

    Now your phone is on in flash interface. You should plug it in and your phone should be attached
    as a Neptune Flash Interface (or whatever type of phone yours is).

    You will then need to use a moster flash to recover it.
    A monster flash is a flash that includes both a flash file and a flex. These are fairly common. I have no links but there are some on my fserv in the irc channel in my sig.

    Make sure you find an unlocked one. I don't know all of the possible locked/unlocked ones, so that's up to you.

    Some people have managed to flash their phone and flex it seperatly using the flash interface and the se....f9.shx flex, but I haven't had any luck with that.

    Flash using MultiFlashFlex.exe included with PST, and your good to go.

    Unless I missed something, It probably wont help you recover your phone. This DOES work, I've tested it several times with several phones using several flashes to mess them up.


  10. Default them of motoroker e

    cna any one tell me how to download them on e6

    my e mail id is * E-mail removed




    Quote Originally Posted by ash1986 Log in to see links
    MICRO-TAC "FLIP" SERIES

    This phone follows similar methods as outlined for the 8000 series above.

    Remove the battery and locate the three contacts at the bottom of the phone, the two outer contacts are raised and connect with the battery. The center contact is recessed, this is the Manual Test Mode connector.

    Now look at the battery contacts, the two outer ones supply power to the phone, the center contact is an "extra" ground. This ground needs to be shorted to the test mode connector on the phone. The easiest way to do this is to put a small piece of solder wick, wire, aluminum foil or any other conductive material into the recess on the phone. Having done this carefully replace the battery and turn on the power, if you have been successful the phone will wake up in test mode.

    TEST MODE PROGRAMING:

    Assuming you have completed one of the above steps correctly the phone will wake up in test mode when you turn the power on. When you first access test mode the phone's display will alternate between various status information that includes the received signal strength and channel number. The phone will operate normally in this mode. You can now access Service Mode by pressing the # key, the display will clear and a ' will appear. Use the following procedure to program the phone:

    1. Enter 55# to access programing mode.
    2. The * key advances to the next step. (NOTE that test mode programing does NOT have step numbers, each time you press the * key the phone will display the next data entry).
    3. The CLR key will revert the display to the previously stored data.
    4. The # key aborts programing at any time.
    5. To complete programing you must scroll through ALL entries until a ' appears in the display.
    6. Note that some entries contain more digits than can be displayed by the phone, in this case only the last part of the data can be seen.

    TEST MODE PROGRAMING DATA:

    STEP# #OF DIGITS/RANGE DESCRIPTION

    01 00000 - 32767 SYSTEM ID
    02 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 1 BELOW
    03 10 DIGITS MIN (AREA CODE & TEL#)
    04 2 DIGITS STATION CLASS MARK
    05 2 DIGITS ACCESS OVERLOAD CLASS
    06 2 DIGITS GROUP ID (10 IN USA)
    07 6 DIGITS SECURITY CODE
    08 3 DIGITS LOCK CODE
    09 3 DIGITS SERVICE LEVEL (LEAVE AT 004)
    10 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 2 BELOW
    11 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 3 BELOW
    12 0333 OR 0334 INITIAL PAGING CHANNEL
    13 0333 "A" SYSTEM IPCH
    14 0334 "B" SYSTEM IPCH
    15 3 DIGIT NUMBER PAGING CHANNEL (021 IN USA)
    16 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 4 BELOW
    Last edited by Kevin; 01-05-2008 at 08:53 AM.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •